Water transfer printing films - new products

Processing instructions for the water transfer printing film Stickerbomb Grob WT-1803 in various widths: For the Stickerbomb Grob WT-1803 film, the water in the basin should have a temperature of 25-27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-painting or priming is required for all parts not made of ABS plastic.

Read more less

Processing instructions for the water transfer printing film Carbon Silver Coarse WT-1808 in 1 meter width: For the Carbon Silver Coarse WT-1808 film, the water in the basin should have a temperature of 25-27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-coating or priming is required for all parts not made of ABS plastic.

Read more less

Processing instructions for the water transfer printing film Skulls with Flowers WT-1807 in 1 meter width: For the Sticker Girls WT-1804 film, the water in the basin should have a temperature of 25-27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-painting or priming is required for all parts not made of ABS plastic.

Read more less

Processing instructions for the water transfer printing film Flowers Pink WT-1806 in various widths: For the Pink Floral WT-1806 film, the water in the basin should have a temperature of 25-27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-coating or priming is required for all parts not made of ABS plastic.

Read more less

Processing instructions for the water transfer printing film Henna Silver WT-1805 in various widths: For the Henna Silver WT-1805 film, the water in the basin should have a temperature of 25-27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-coating or priming is required for all parts not made of ABS plastic.

Read more less

Instructions for applying the water transfer printing film Sticker Girls WT-1804 in various widths: For the Sticker Girls WT-1804 film, the water in the basin should be between 25 and 27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-painting or priming is required for all parts not made of ABS plastic.

Read more less

Processing instructions for the water transfer printing film Stickerbomb Grob WT-1803 in various widths: For the Stickerbomb Grob WT-1803 film, the water in the basin should have a temperature of 25-27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-painting or priming is required for all parts not made of ABS plastic.

Read more less

Processing instructions for the water transfer printing film Letter Black WT-1802 in various widths: For the Letter Black WT-1802 film, the water in the basin should have a temperature of 25-27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-coating or priming is required for all parts not made of ABS plastic.

Read more less

Processing instructions for the water transfer printing film US Flags in blue/red WT-1709 in various widths: For the US Flags blue/red WT-1709 film, the water in the basin should be between 25 and 27°C. The soaking time is 60 seconds. There are two options before placing the film in the water: 1. Make cuts all around the film at a 45° angle, spaced 2-3 cm apart. At the end of the 60-second soaking time, spray the film with activator and immerse the component immediately. Pre-painting or priming is required for all parts not made of ABS plastic.

Read more less